Yinma Electric Technical Column · Xu Jianye

S11-M Hermetically Sealed Oil-Immersed Transformer Selection
China Transformer Guide · GB/T 6451 vs IEC 60076

Yinma Electric Co., Ltd. is a China transformer manufacturer in Yueqing, Zhejiang, supplying S11-M oil-immersed distribution transformers to 11 kV / 33 kV African networks. Engineer Xu Jianye wrote this guide from GB 1094, GB/T 6451 and IEC 60076 — ratings, losses, tests and how to specify.

S11-M
Product series
11kV·33kV
Voltage class
GB·IEC
Standards
50Hz·ONAN
Service

Three items to lock before buying a China transformer

If rating, standard and site climate are not written into the enquiry, the type-test file and the customs file will not match.

    Rating code. S9 / S11 / S13 / S(B)H15 are loss sequences in GB/T 6451 and GB/T 25446 — not brand names. Standard. A China transformer is type-tested to GB 1094; African utilities accept IEC 60076. Mapping is below. Environment. Altitude, maximum ambient and salt fog set external insulation and temperature-rise corrections. If they are omitted, the factory designs for 1 000 m / 40 °C.

What S11-M means in the standard

Oil-immersed distribution transformer type codes in China are defined in GB/T 6451.

S three-phase; 11 loss sequence 11 (a higher number means a lower no-load and load-loss cap); M hermetically sealed — no conservator, corrugated tank compensates oil volume. Example S11-M-500/10: 500 kVA, HV 10 kV. For an 11 kV African feeder, specify rated voltage 11 kV (or 10.5/11 kV) so the winding is designed to that voltage. Do not stretch a 10 kV nameplate with taps.

SequenceStandardNo-load loss vs S11Where it is used
S9GB/T 6451 sequence 9About 25%–30% higherWithdrawn in China; Africa spare-parts stock
S11GB/T 6451 sequence 11BaselineMainstream new African distribution feeders
S13GB/T 6451 sequence 13About 20% lowerCurrent China GB 20052 market access level
S(B)H15GB/T 25446 amorphousAbout 60%–70% lowerDaily load factor typically below ~30%

The current GB 20052 edition raised China domestic energy-efficiency access to the S13 equivalent. S11 lines in a China transformer factory therefore mainly serve IEC 60076 markets. The GB/T 6451 sequence-11 limits remain valid, and most African utility specifications still accept them — an export-compliant product, not leftover stock.

Core, windings, oil-paper insulation, sealed tank

These four items set losses, temperature rise and short-circuit withstand.

01

Core

CRGO, 45° mitred joints. Mitring cuts corner reluctance — the main reason S11 no-load loss is about 25%–30% below S9. No-load current I₀% is a direct check of stacking quality.

02

Windings

HV layer winding; LV cylindrical or helical copper. Axial and radial clamping is the GB 1094.5 / IEC 60076-5 short-circuit force path. African 11 kV/0.4 kV units are normally Dyn11, 50 Hz.

03

Oil-paper · ONAN

Class A (105 °C). GB 1094.2 / IEC 60076-2: top-oil 60 K, average winding 65 K. Cooling is oil-natural air-natural ONAN. Oil to GB 2536 / IEC 60296.

04

Hermetic (-M)

Corrugated tank takes thermal expansion; conservator and dehydrating breather are omitted. Oil is isolated from air. Sealing is tested to GB/T 6451. Prefer -M on unmanned kiosks; keep a conservator if site oil sampling is required.

Quantities that must match the routine-test report

Check against GB/T 6451 sequence 11 and the GB 1094.1 / IEC 60076-1 routine-test list.

QuantityMeaningTypical limit / contract value
P₀ no-load lossIron loss, independent of load, continuousGB/T 6451 sequence 11 table by kVA
Pₖ load lossCopper + stray, ∝ I², referred to 75 °CSame table; at low load factor annual kWh is dominated by P₀
I₀%Magnetising current / rated currentGB/T 6451 limit; high values usually mean stacking issues
Uₖ%Short-circuit impedance10 kV class ≤630 kVA typically 4.0%; 800–1600 kVA 4.5%; 35 kV class typically 6.5%
Insulation levelLI / AC12 kV equipment: LI 75 kV / AC 35 kV; 36 kV equipment: LI 170 or 200 kV / AC 70 or 85 kV — as contracted
Temperature riseTop oil / winding60 K / 65 K (ONAN)
TappingsOff-circuit tap-changerTypically ±2×2.5%; must cover local voltage deviation
Short-circuitIEC 60076-5 / GB 1094.5Rated short-circuit current for the agreed duration (commonly 2 s); special test

Parallel operation needs three extra checks: identical vector group, capacity ratio not more than 3:1, Uₖ preferably within ±10%. When a new China transformer is paralleled with existing plant on an African industrial park, these three lines are the ones most often missing from the RFQ.

China transformer standards GB vs IEC 60076

Factory tests follow GB 1094; African bid evaluation follows IEC 60076. Put both numbers on the same report.

SubjectChina transformer standardIEC
General, ratings, test classificationGB 1094.1IEC 60076-1
Temperature riseGB 1094.2IEC 60076-2
Insulation and external clearancesGB 1094.3IEC 60076-3
Short-circuit withstandGB 1094.5IEC 60076-5
Loss sequences S9 / S11 / S13GB/T 6451No IEC twin; African specs often quote the loss table
Amorphous alloyGB/T 25446—
Transformer oilGB 2536IEC 60296

Routine tests (every unit): winding resistance, voltage ratio and vector group, no-load, load and impedance, power-frequency withstand. Type tests: temperature rise, lightning impulse. Special tests: short-circuit withstand, as contracted. Acceptance: report serial = nameplate serial; the type-test file must cover the bid kVA and insulation level; SONCAP (Nigeria), KEBS PVoC (Kenya) and SANS (South Africa) before shipment.

Yinma Electric S13-M-2000/10 oil-immersed transformer type test report cover, CNAS L0116, report No.2013345697
Type-test report cover — Yinma Electric S13-M-2000/10 oil-immersed power transformer. Issuing body: State Center of Supervision Test for Electrical Safety (Zhejiang) / Zhejiang Fangyuan Electrical Equipment Testing Co., Ltd. (CNAS L0116, ILAC-MRA). Report No. 2013345697.
Page 1 of Yinma Electric S13-M-2000/10 type test report listing GB/T 1094.1/.2/.3/.5 and GB/T 6451-2015
Report page 1 — manufacturer and applicant: Yinma Electric Co., Ltd., 358 Chengxi Road, Lecheng, Yueqing, Zhejiang. Sample dated July 2020; tests 18–27 September 2020. Basis: GB/T 1094.1-2013, GB/T 1094.2-2013, GB/T 1094.3-2017, GB/T 1094.5-2008, GB/T 1094.10-2003, GB/T 6451-2015. Scope: routine + type + special tests, all within the standard limits.

This file is a sealed oil-immersed unit of the same construction family as S11-M (the tested sample is S13-M-2000/10 — a lower-loss sequence than S11). It shows how a China transformer factory documents GB 1094 routine, type and special tests, including short-circuit withstand (GB/T 1094.5). Ask for a type-test report that covers the kVA and insulation level in your bid; do not accept a smaller-kVA report as a substitute.

Five parameters fix a China transformer design

Write these five lines into the RFQ and the factory can lock kVA, loss sequence, tank type and the test list.

Voltage and rating

HV 11/15/33 kV, LV 400/415 V, 50 Hz. S = P / cosφ, then 20%–25% growth margin. Continuous load factor should not stay above 80%.

Load factor → loss sequence

Daily mean ≥40%: S11. High continuous load: S13. Daily mean <30%: check whether S(B)H15 P₀ savings cover the extra price.

Altitude and ambient

Default design: 1 000 m / 40 °C. Above that, reduce allowable temperature rise per GB 1094.2 / IEC 60076-2 (ONAN common rule: 1 K per additional 400 m) and increase external clearances or creepage per GB 1094.3 / IEC 60076-3. Stamp design altitude on the nameplate.

Construction

Unmanned kiosk: hermetic S11-M. Coastal sites: state paint thickness and corrosion class. If ±2×2.5% taps are not enough, widen the range in the protocol.

Documents

Routine tests + type tests covering the bid type + certificate of conformity + destination-country CoC. Write GB 1094.x / IEC 60076-x. Do not write “factory standard”.

Destination-country checklist

Voltage, conformity mark and climate are three separate lines. Do not reuse one default protocol for the whole continent.

MarketTypical voltageConformityDesign note
Nigeria11 / 33 kVSONCAPWide voltage swing; put tap range in the contract
Kenya11 / 33 kVKEBS PVoC1 500–2 500 m — correct both rise and external insulation
South Africa11 / 22 kVSANSMining inrush; check Uₖ and short-circuit withstand
Ethiopia15 / 33 kVBid specUsually >1 800 m; agree 15 kV insulation level separately
Zambia / Tanzania11 / 33 kVBid specLong inland haul; write sealing and packing into the contract

Voltage, kVA, load factor, altitude, maximum ambient — five lines in the enquiry are enough for a China transformer factory to freeze the winding, insulation and test plan.

— Xu Jianye, Yinma Electric design engineer

Four technical questions at bid stage

    Has China withdrawn S11? Domestic access under GB 20052 is now S13. Export units are still built to GB/T 6451 sequence 11 and are widely accepted in African specs.

    Can a GB test report be used under IEC? GB 1094.1/.2/.3/.5 map to IEC 60076-1/-2/-3/-5. Require the China transformer supplier to print both numbers on the same report.

    Can a 10 kV unit run on 11 kV? Insulation is the same 12 kV equipment class (LI75/AC35), but turns ratio is not. Order an 11 kV China oil-immersed transformer; use taps only for fine voltage correction.

    How do you verify a China transformer factory? (1) Type-test kVA and insulation cover the bid. (2) Manufacturing, not trading only. (3) SONCAP / KEBS handling record. (4) Protocol states standard numbers, Uₖ, Dyn11, ONAN and design altitude.

Author and manufacturer

Xu Jianye is a design engineer at Yinma Electric Co., Ltd., responsible for oil-immersed transformer export protocols and GB 1094 / GB/T 6451 / IEC 60076 test mapping. Yinma Electric is a China transformer manufacturer and exporter in Yueqing, Zhejiang, supplying distribution transformers and switchgear to Africa, the Middle East and Southeast Asia. Contract values follow the signed technical protocol; standards follow the latest in-force edition.

Enquire with five parameters
Voltage · kVA · load factor · altitude · maximum ambient

Yinma Electric will return loss-sequence advice, GB/IEC mapping and the factory test list for 11 kV / 33 kV African projects.

Further Reading

Yinma Electric SCB18 cast-resin dry-type transformer
Technical Guide

SCB18 Dry-Type Transformer Selection: China Cast-Resin GB/T 10228 vs IEC 60076-11

Engineer Xu Jianye maps SCB18-NX1 ratings, AN cooling, Dyn11, and GB/T 1094.11 type tests to IEC 60076-11 — with Yinma Electric’s CNAS type-test report for indoor African 11 kV substations.

Read Article →
Yinma Electric MNS withdrawable low-voltage switchgear lineup
Technical Guide

MNS Withdrawable LV Switchgear Selection: China LV Switchgear GB 7251.12 vs IEC 61439-2

Engineer Xu Jianye maps MNS drawer ratings, bus Icw, indoor IP30, and GB 7251.12 type tests to IEC 61439-2 — with Yinma Electric’s 2015 CNAS/CCC file for African 400/415 V rooms.

Read Article →
Yinma Electric YB-12 HV/LV prefabricated compact substation kiosk
Technical Guide

YB-12 Compact Substation Selection: China Package Substation GB/T 17467 vs IEC 62271-202

Engineer Xu Jianye maps YB□-12/0.4-1250 kiosk ratings, three compartments, and GB/T 17467 type tests to IEC 62271-202 — with Yinma Electric’s CNAS report for African 11 kV pad-mount sites.

Read Article →

Need Technical Support or a Quote?

Our engineering team can answer follow-up questions about this article and provide specifications, pricing, and delivery schedules for your project.

Technical parameters