Yinma Electric Technical Column · Xu Jianye

SCB18 Cast-Resin Dry-Type Transformer Selection
China Dry-Type Transformer · GB/T 10228, GB/T 1094.11 and IEC 60076-11

Yinma Electric Co., Ltd. is a China transformer manufacturer in Yueqing, Zhejiang, supplying SCB-series cast-resin dry-type transformers for indoor African 11 kV / 33 kV substations. Engineer Xu Jianye wrote this guide from GB/T 1094.11, GB/T 10228, GB 20052 and IEC 60076-11 — ratings, losses, type tests and how to specify.

SCB18
Product series
11kV·NX1
Voltage · EE class
GB·IEC
Standards
50Hz·AN
Service

Three items to lock before buying a China dry-type transformer

Indoor dry-type units fail tenders when the loss sequence, IEC 60076-11 environmental class and enclosure IP are left blank.

    Rating code. SCB10 / SCB12 / SCB14 / SCB18 are loss sequences in GB/T 10228 — not brand names. The suffix NX1 on a nameplate is GB 20052 energy-efficiency Grade 1. Standard. A China dry-type transformer is type-tested to GB/T 1094.11; African indoor specs quote IEC 60076-11. Mapping is below. Installation. Indoor vs outdoor, AN or AF cooling, IP20–IP54 enclosure, and climatic class (C1/C2) must be written into the protocol. If omitted, the factory designs for indoor AN, IP20, 1 000 m / 40 °C.

What SCB18-2000/10-NX1 means

Cast-resin dry-type codes in China are defined in GB/T 10228 《干式电力变压器技术参数和要求》.

S three-phase; C epoxy-resin cast (solid insulation); B foil LV winding; 18 loss sequence 18 (a higher number means a lower no-load and load-loss cap); 2000/10 2 000 kVA, HV 10 kV; NX1 GB 20052 Grade 1 energy efficiency. For an 11 kV African indoor feeder, specify rated voltage 11 kV (or 10.5/11 kV). Do not stretch a 10 kV nameplate with taps.

SequenceStandardRelative no-load lossWhere it is used
SCB10GB/T 10228 sequence 10Baseline of earlier Chinese dry-type stockOlder indoor plant; Africa spare-parts enquiries
SCB12 / SCB14GB/T 10228 sequences 12 / 14Lower than SCB10Common export indoor substations
SCB18GB/T 10228 sequence 18Lower than SCB14 (check the table for the kVA)Current high-efficiency indoor units
SCB18-NX1GB 20052-2020 Grade 1Meets China Grade 1 EE limits at that kVATenders that quote GB 20052 or equivalent IEC efficiency

GB 20052-2020 sets energy-efficiency grades for both oil-immersed and dry-type distribution transformers in China. NX1 on the tested sample SCB18-2000/10-NX1 means the unit was assessed against Grade 1 limits, not a marketing suffix. African indoor specs that quote IEC 60076-11 still need the loss table (P₀, Pₖ) written as numbers — do not assume “SCB18” is understood outside China.

Core, resin-cast windings, AN cooling, enclosure

These four items set losses, temperature rise, fire behaviour and short-circuit withstand.

01

Core

CRGO, typically 45° mitred joints. No-load loss P₀ and no-load current I₀% are the stacking check on the routine-test report (GB/T 1094.1 / IEC 60076-1).

02

Cast windings

HV windings vacuum-cast in epoxy; LV usually copper foil (the “B” in SCB). Casting quality governs partial discharge and moisture ingress. African 11 kV/0.4 kV indoor units are normally Dyn11, 50 Hz.

03

Insulation · AN / AF

Typical thermal class F (155 °C). Winding temperature-rise limits follow GB/T 1094.11 / IEC 60076-11 for the declared class. Cooling is air-natural AN; fans (AF) are a contract option for cyclic overload, not a substitute for kVA.

04

Enclosure & classes

Indoor default IP20. Coastal or dusty plant rooms need a stated IP and IEC 60076-11 climatic / environmental / fire classes (commonly C2, E2, F1). These letters must appear in the protocol; they are not implied by “dry type”.

Quantities that must match the routine-test report

Check against GB/T 10228 for the declared sequence and the GB/T 1094.1 / IEC 60076-1 routine-test list.

QuantityMeaningTypical limit / contract value
P₀ no-load lossIron loss, continuousGB/T 10228 table for the SCB sequence and kVA
Pₖ load lossCopper + stray, ∝ I², referred to the rated winding temperatureSame table; indoor plant with low night load is still dominated by P₀
I₀%Magnetising current / rated currentGB/T 10228 limit
Uₖ%Short-circuit impedance10 kV class mid-kVA typically ~6%; confirm from GB/T 10228 for the exact kVA
Insulation levelLI / AC12 kV equipment: typically LI 75 kV / AC 35 kV — as contracted
Partial dischargeGB/T 1094.11 / IEC 60076-11Routine or type item as contracted; cast-resin quality check
Sound levelGB/T 1094.10 / IEC 60076-10Indoor commercial rooms: write a dB(A) cap, do not leave “standard”
Short-circuitGB/T 1094.5 / IEC 60076-5Special test; duration commonly 2 s if specified

Parallel operation still needs identical vector group, capacity ratio not more than 3:1, and Uₖ preferably within ±10%. Mixing an oil-immersed outdoor unit with an indoor dry-type on the same LV bus is a protection-coordination problem, not a “loss sequence” problem — write the SLD before the RFQ.

China dry-type transformer standards GB vs IEC 60076-11

Factory tests follow GB/T 1094.11 and GB/T 10228; African indoor bid evaluation follows IEC 60076-11. Put both numbers on the same report.

SubjectChina dry-type standardIEC
General, ratings, test classificationGB/T 1094.1IEC 60076-1
Insulation and external clearancesGB/T 1094.3IEC 60076-3
Short-circuit withstandGB/T 1094.5IEC 60076-5
Sound levelsGB/T 1094.10IEC 60076-10
Dry-type transformersGB/T 1094.11IEC 60076-11
Loss and parameter tablesGB/T 10228No IEC twin; quote P₀ / Pₖ numbers
Energy-efficiency gradesGB 20052-2020National EE rules differ by country

Routine tests (every unit): winding resistance, voltage ratio and vector group, no-load, load and impedance, applied voltage, induced voltage, and partial discharge where contracted. Type tests: temperature rise, lightning impulse, and others listed on the cover. Special tests: short-circuit withstand, sound, as contracted. Acceptance: report serial = nameplate serial; the type-test file must cover the bid kVA, insulation level and thermal class.

Yinma Electric SCB18-2000/10-NX1 dry-type transformer type test report cover, CNAS L0116, report No.22133B40372
Type-test report cover — Yinma Electric SCB18-2000/10-NX1 cast-resin dry-type transformer. Issuing body: Zhejiang Fangyuan Testing Group / Zhejiang Fangyuan Electrical Equipment Testing Co., Ltd. / National Center of Quality Inspection for Electrical Safety (Zhejiang) (CNAS L0116, ILAC-MRA). Report No. 22133B40372. Test category: type test.
Page 1 of Yinma Electric SCB18-2000/10-NX1 type test report listing GB/T 1094.11, GB/T 10228-2015 and GB 20052-2020
Report page 1 — manufacturer and applicant: Yinma Electric Co., Ltd., 358 Chengxi Road, Lecheng, Yueqing, Zhejiang. Sample dated March 2022; tests 22–30 March 2022 at Jiaxing. Basis: GB/T 1094.1-2013, GB/T 1094.3-2017, GB/T 1094.5-2008, GB/T 1094.10-2003, GB/T 1094.11-2007, GB/T 10228-2015, GB 20052-2020. Scope: routine + type + special tests, all within the standard limits. Approved 4 April 2022.

This file is the type-test package for the exact series discussed in this article (SCB18-2000/10-NX1). It documents how a China dry-type transformer factory records GB/T 1094.11, GB/T 10228 and GB 20052 on one cover, including short-circuit (GB/T 1094.5) and sound (GB/T 1094.10). Ask for a type-test report that covers the kVA, insulation level and NX grade in your bid; do not accept a smaller-kVA or oil-immersed report as a substitute.

Five parameters fix a China dry-type transformer design

Write these five lines into the RFQ and the factory can lock kVA, loss sequence, enclosure and the test list.

Voltage and rating

HV 11/15/33 kV, LV 400/415 V, 50 Hz, Dyn11 unless the LV board says otherwise. S = P / cosφ, then 20%–25% growth margin. Indoor rooms with poor ventilation need a stated maximum ambient, not the 40 °C default.

Loss sequence and NX grade

Quote P₀ and Pₖ from GB/T 10228 for the chosen SCB sequence, or require NX1 / Grade 1 if the tender cites GB 20052. “High efficiency” without numbers is not a specification.

AN / AF and IP

AN for continuous indoor load within nameplate kVA. AF only if cyclic overload is calculated. Coastal or cement-plant rooms: state IP and C2/E2/F1 classes per IEC 60076-11.

Sound and fire

Hospitals, malls and high-rise plant rooms: write a sound-level cap (GB/T 1094.10 / IEC 60076-10) and fire class F1 if the building code requires it. Dry-type is not automatically F1.

Documents

Routine tests + type tests covering the bid type + certificate of conformity + destination-country CoC (SONCAP / KEBS PVoC / SANS). Write GB/T 1094.11 / IEC 60076-11. Do not write “factory standard”.

When a dry-type belongs on the RFQ — and when it does not

Cast-resin indoor units solve fire and oil-containment rules. They do not replace outdoor oil-immersed pole or pad units on rural feeders.

Typical indoor useWhy dry-typeSpecify in the protocol
Mall, hospital, high-rise, data hallNo oil pit; fire compartment rulesSound dB(A), F1 if required, IP, max ambient
Industrial plant room next to processIndoor step-down beside LV boardsHarmonics / K-factor if VFD heavy; AN or AF
Coastal city indoor substationResin vs oil leak in a basementC2/E2, enclosure IP, anti-corrosion hardware
Rural 11 kV pole / pad outdoorNot the dry-type use caseSpecify oil-immersed S11-M / S13-M instead

Voltage, kVA, P₀/Pₖ or NX grade, IP plus C2/E2/F1, maximum ambient — five lines are enough for a China dry-type transformer factory to freeze the winding, enclosure and test plan.

— Xu Jianye, Yinma Electric design engineer

Four technical questions at bid stage

    Is SCB18 a China-only code? Yes. Write the GB/T 10228 P₀ and Pₖ values (and NX1 if Grade 1 is required) so an IEC 60076-11 evaluator can score the bid without knowing the SCB letters.

    Can a GB/T 1094.11 report be used under IEC 60076-11? The parts listed on Yinma’s SCB18-2000/10-NX1 cover map to IEC 60076-1/-3/-5/-10/-11. Require both numbers on the same report.

    Does dry-type remove the need for fire protection? No. IEC 60076-11 fire class F1 is a declared option. State it if the building code needs it.

    How do you verify a China dry-type transformer factory? (1) Type-test kVA, insulation and NX grade cover the bid. (2) Manufacturing, not trading only. (3) SONCAP / KEBS handling record. (4) Protocol states GB/T 1094.11 / IEC 60076-11, Uₖ, Dyn11, AN/AF, IP and C2/E2/F1.

Author and manufacturer

Xu Jianye is a design engineer at Yinma Electric Co., Ltd., responsible for dry-type and oil-immersed transformer export protocols and GB/T 1094 / GB/T 10228 / IEC 60076-11 test mapping. Yinma Electric is a China transformer manufacturer and exporter in Yueqing, Zhejiang. Contract values follow the signed technical protocol; standards follow the latest in-force edition.

Enquire with five parameters
Voltage · kVA · P₀/Pₖ or NX grade · IP / C2 E2 F1 · maximum ambient

Yinma Electric will return SCB-sequence advice, GB/IEC mapping and the factory test list for indoor African 11 kV / 33 kV substations.

Further Reading

Yinma Electric S11-M hermetically sealed oil-immersed distribution transformer
Technical Guide

S11-M Sealed Oil Transformer Selection: China Transformer GB/T 6451 vs IEC 60076

Engineer Xu Jianye maps S11-M ratings, ONAN temperature rise, Dyn11, and GB 1094 type tests to IEC 60076 — with Yinma Electric’s CNAS type-test report for African 11 kV / 33 kV buyers.

Read Article →
Yinma Electric MNS withdrawable low-voltage switchgear lineup
Technical Guide

MNS Withdrawable LV Switchgear Selection: China LV Switchgear GB 7251.12 vs IEC 61439-2

Engineer Xu Jianye maps MNS drawer ratings, bus Icw, indoor IP30, and GB 7251.12 type tests to IEC 61439-2 — with Yinma Electric’s 2015 CNAS/CCC file for African 400/415 V rooms.

Read Article →
Yinma Electric YB-12 HV/LV prefabricated compact substation kiosk
Technical Guide

YB-12 Compact Substation Selection: China Package Substation GB/T 17467 vs IEC 62271-202

Engineer Xu Jianye maps YB□-12/0.4-1250 kiosk ratings, three compartments, and GB/T 17467 type tests to IEC 62271-202 — with Yinma Electric’s CNAS report for African 11 kV pad-mount sites.

Read Article →

Need Technical Support or a Quote?

Our engineering team can answer follow-up questions about this article and provide specifications, pricing, and delivery schedules for your project.

Technical parameters